Incorrect values, procedures and or tools may cause damage to the engine and or personal injury. The oil jetting out from the nozzle is at a high pressure to cause loss of sight or injury if coming into careless contact with it. The cams have a curve that minimized the repeated shocks on the valve seats and maximizes valve seat life. Idle gear shaft Idle gear 29 Removing the camshaft 1 Push up tappet by turning a camshaft to remove it from the cylinder block easily. Hold the pressure for about 5 seconds at a little before the valve opening pressure of 1. This engineered system of Worse cables, control head and engine connection kits ensures dependable, smooth operation with an absolute minimum of backlash.
Disassembly and reassembly 30 Removing the gear case Liquid gasket 1 Remove the gear case from the cylinder block. For accident prevention, it is important to avoid such causes before development to accidents. There is no fuel oil in the fuel Supply fuel and bleed the system injection pump tank 2. There is no fuel oil in the fuel Supply fuel and bleed the system injection pump tank 2. The most important tool in your toolbox may be your Clymer manual -- get one today. Incorrect values, procedures and or tools may cause damage to the engine and or personal injury.
Inspection and Servicing of Basic Engine Parts 3 Removing the piston pin A floating type piston pin is used in this engine. To prevent seizure in the event of the filter clogging up, a bypass circuit is provided in the oil filter. Damage to the engine, shortened engine life and or personal injury may result. It is difficult to disassemble and, once disassembled, even more difficult to reassemble. Otherwise, it results in engine damage, uneven engine performance and shorten engine life. These are designed specifically for use with Morse control heads. Disassembly and reassembly 21 Turning the engine over Bolt 1 Place a wood block of appropriate size on the floor, and stand up the engine on the flywheel housing.
Engine starts, but 1 Fuel pipe is clogged. Check to be sure that the strainer is in the water before turning on the switch. Cooling water system 7 The pump cannot be used to drain off rain water or large amounts of flood water. Inspection and Servicing of Basic Engine Parts 5. Governor The emergency stop button is integrated with the Stop solenoid solenoid. Service standards 5 Tappet and push rod Reference Inspection item Standard Limit page Tappet outside diameter 20. Inspection and Adjustment 7 Check the leakage of water, lube oil and fuel.
The large end with the aluminium metal can be separated into two and the small end has a 2-layer copper alloy coil bushing. Inspection and Adjustment 2 Checking marine gear lube oil level a Check the lube oil level of the marine gear with a Oil filler cap dipstick. Usually do not open the filler cap to check or replenish. The coolant recovery tank maintains the water level by preventing this discharge of water. .
The original height of mounting blocks is shown in this drawing. Torque wrench Used to tighten bolts and nuts to standard torque. Inspection and servicing of basic engine parts 5. The cause of the trouble may not necessarily be in the pump itself, but may be in the engine or the fuel system. The features are compactness, waterproof and independence from pulse by ring gear teeth number. Never approach the injection nozzle portion with a hand.
Oil pressure lamp 1 Visual inspection. V-pulley Shaft Retaining ring Ball bearing Spacer Retaining ring O-ring Ball bearing Plate Cover O-ring. The cable will become stretched and the attachments loose after long hours of use causing deviation. Inspection and Servicing of Basic Engine Parts 5. Disassembly and reassembly 11 Mounting the idling gear Upside 1 Mount the idling gear so that the mark of the idle Mark gear shaft upward. Three Bond 200g Non-drying liquid gasket ;.
After this time it must shut off for a period of 2 hours before reusing. The cartridge type filter is easy to remove. Please read this manual carefully before starting repair or maintenance to fully understand safety precautions and appropriate inspection and maintenance procedures. Photoelectric Measures rotation speed by using a type reflector mark which is placed on the Revolving shaft exterior of the revolving shaft. I-9 Adjust to correct position.
The specific gravity of Float battery electrolyte is defined with 20 C as the standard. The piston pin can be pressed into the piston pin hole at room temperature Coat with oil to make it slide easily. The hose attached at the nozzle should be 1. Inspection and Servicing of Basic Engine Parts 6 Spring retainer and spring cotter Inspect the inside face of the spring retainer, the outside surface of the spring cotter, the contact area of the spring cotter inside surface and the notch in the head of the valve stem. The hose attached at the nozzle should be 1. Faulty battery Check to see if the specific gravity of the battery fluid is greater than 1.