In some cases the manufacturer does not allow us to show you our lower prices until you take further action. Open the hood and remove the black negative battery cable from the battery. It will be black and have a flat plastic tab. Note the position of the filter and mark the in and out hoses of the filter. Loosen the clamps on the hoses and pull the hoses out gently, holding the filter horizontally to prevent the left over fuel from spilling. You may have to before you can post: click the register link above to proceed. Pull the fronts first, from the corners.
There are two types of connectors that fit the fuel lines to the filter. Push the floor jack under the Jetta on the support beams of the body frame and jack the Jetta up to a point you can comfortably slide under the car and use hand tools. I also used the Wix 33521 fuel filter as a replacement for the factory filter. When picking a reliable brand name for your intake system's fuel pump, trust Airtex. To get the filter out push the tabs of the frame slightly forward, lift the frame up, and pull it towards you.
After disconnecting the speaker lead this section of the dash can be moved out of the way. So, your fuel filter becomes the final line of defense against damaging contaminants getting into your vehicle. Locate the quick-connect fitting on the clamp and fuel filter. Should be no different for the 2006. Mine had a Philips head hose clamp wrapped around it I know it looks like a flat head only but it actually is a Phillips or flat head which ever you prefer This clamp has to be completely unscrewed so the filter will release from the car. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.
Standing in front of the car, you will see the plastic cowel that lines the bottom of your windshields. When the vehicle is running -- inspect for any leaks. Once out you will see your filter. Turn the screws to the left to loosen them. It is a tight … fit and requires a little wiggle and a wobble here and there. If the bolts don't seem to be going in then you will have to slowly raise the engine or lower it till the bolt matched the engine support bracket. The adapter required to make it work was developed by Greg Landuyt of fame.
So I know this is super simple and most of you probably know exactly how to do it but I hope I help someone. This is why it cost so much to get it done at the dealership because of the labor time. Now locate the fuel tank under the car, on the driver side of it you will have to unhook the emmisions bleeder valve, be sure to do this fast so the fumes do not build up under the car. We only sell parts from trusted brands like so that you can find quality parts you can count on. Take the gas cap off for a minute or so.
Clean fuel, free from dirt particles and rust, is essential for the smooth and efficient operation of your vehicle. I have one on my car and it holds up really well and you can go more miles than the stock if you are getting good quality fuel. I only took picture on the end closest to me the opposite end is exactly the same. After you get the tab pushed all the way in you'll want to gently twist and pull off the clamp with the tab still depressed. Part number is: 1J0 201 511A Thanks for this write up I am going to do it tomorrow morning as it will be better for the fuel lines to clear a bit so ita ok getting it off cant wait hope I dont mess up. All and all not a hard project but I sure hate those compression clips, or whatever they are called. You must note that their are 2 types one that has the pipes screwed onto the filter and the other has push over and clamp on type fittings.
It is located on your dash board above the radio remove it ,cabin air filter is there i hope that helps. By ensuring we follow manufacturer advertising guidelines, AutoPartsWarehouse. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence. Ensure the edges are seated. You'll probably have a little difficulty at first , but if you just keep cranking it don't be afraid diesels are tough! The passenger side dash can then be detached by slowly lifting the left side of it straight up and then sliding it to the left. Unless otherwise indicated, all prices exclude applicable taxes and installation costs. Lift the front edge up out of the box and pull forward as before, wiggle wobble needed again.
For safer or pleasant drive, regular automobile check-up is recommended. Push the tab with the flat end of the screwdriver to open the fuel filter housing and let the fuel filter drain into the pan for around 20 minutes. There are 5 screws to undo no need to take them out, just unscrew. This problem occurs completely at random, regardless of fuel level, incline, or throttle position. Ensure the edges are seated.
No matter the situation, Advance Auto Parts has the Fuel Filter product you desperately need. All Replacement brand items are backed by 1-year, unlimited-mileage warranty. Not necessarily a big deal, just want you to be informed. Thanks and Good Luck Well written, I'm glad you took the time to do this. It is held in by a screw type clamp about half way down the cylinder. What am I suppose to do with a 2 year car with major fire damage.
A tiny grain of dirt can clog injectors, leading to erratic performance and poor gas mileage. Slide the filter forward, toward the front of the car, to release it from the bracket. Although we endeavour to ensure that the information contained on the website is accurate, as errors may occur from time to time, customers should verify any information in question with a dealer. Find the fuel filter next to the gas tank, under the passenger side of the vehicle. Use a new O-ring when reattaching the control valve to the filter top. Some items may be unavailable for or incompatible with certain trim levels and models. I removed one side and it popped in without too much fuss.