2000 range rover manual. Land Rover Service Manuals 2019-02-04

2000 range rover manual Rating: 7,2/10 390 reviews

Land Rover Vehicle Guides & Manuals

2000 range rover manual

Install hub assembly to lower joint, fit new nut and tighten to 48 ft. Remove 3 bolts securing brake disc shield. Clean oil cooler pipe connections at transmission and install new O-rings. Always support the vehicle on safety stands. B Bolts 1-8 C Step 1: 15 ft.

Next

Land Rover Vehicle Guides & Manuals

2000 range rover manual

Remove transmission oil cooler pipes from engine clips. All came with the Land Rover kit to turn the spare tire cover in to a picnic table. R Step 1: 7 ft. . Support the fuel tank with a jack. Hardly any vehicles can go with it.

Next

Land Rover Service Manuals

2000 range rover manual

Wait 10-20 minutes for the back-up power to discharge. Secure the steering wheel, then loosen the self locking nut holding the steering wheel to the column. Note orientation of snubber washer. With the wheels in the straight ahead position, the bottom timing mark on the steering column must be aligned with the steering wheel mark, as shown 9. Repeat for the other horn switch.

Next

Land Range Rover 2000 Owners Manual PDF

2000 range rover manual

Disconnect the 2 harness multiplugs and remove airbag module. Tighten cap nuts to 21 ft. Disconnect the radio and cruise control connectors. Remove screw securing horn earth lead to steering wheel. Do not use substitute fasteners.

Next

Land Range Rover 2000 Owners Manual PDF

2000 range rover manual

Remove the supports and lower vehicle. Retailer price, terms and vehicle availability may vary. Remove 2 nuts and bolts securing hub to shock absorber. Position cable tie and multiplug to transfer case bracket. All County models may have had lightstone leather.

Next

20 Most Recent 2000 Land Rover Range Rover Questions & Answers

2000 range rover manual

Loosen the tie rod-to-sub-frame bolt one quarter turn. Fuel Pump psi Ignition Timing deg. Clean drive shaft and flange splines. Tighten bolts to 19 ft. Place the inflator module on a bench or other surface with the bag and trim cover facing up. Raise and support vehicle chassis with safety stands. Remove 2 screws securing fuel filter and release fuel filter from mounting brackets.

Next

SOLVED: Online owners manual 2000 land rover range rover h

2000 range rover manual

Clean shock absorber shaft and bump stop plate. Interior Aromatic leather upholstery and attractive wood trim greet occupants in the roomy interior, which holds five people. If necessary, remove the heat and fire shields. Before servicing the vehicle, refer to the precautions in the beginning of this section. Before servicing the vehicle, be sure to also refer to the precautions in the beginning of this section as well. Remove cruise control switches from steering wheel.

Next

2000 Land Rover Range Rover Specifications, Details, and Data

2000 range rover manual

Secure breather hoses to throttle housing, if equipped. Check for yellow paint marks about 0. Remove 2 screws securing fuel filter and release fuel filter from mounting brackets 19. Position heat and fire shields. Using a fuel recovery appliance, drain the fuel from the tank into a sealed container.

Next

Range Rover P38 2000 Owner´s Handbook

2000 range rover manual

Remove the 4 Torx® screws and release switch units from airbag module. Fit and tighten screw securing horn earth lead to steering wheel. Wait 10-20 minutes for the back-up power to discharge. Always support the vehicle on safety stands. Mark drive plate to torque converter, for refit purposes.

Next

Range Rover P38 2000 Owner´s Handbook

2000 range rover manual

Torque the lower ball joint nut to 100 ft. Connect throttle inner cable to throttle cam and secure outer cable in abutment bracket, if equipped. Connect the feed hose to the coolant pump, and secure with clip. Remove the tools from the axle yoke. Luxurious thick-pile carpet is used for the floor of the cabin and luggage compartment, floor mats are made of black lambs wool. Install tie rod ball joint nut and tighten to 92 ft. Torque the upper nut to 81 ft.

Next